Sherbourn PRE-1 Anleitung zur Fehlerbehebung PDF herunterladen (Seite 10)

Connecting Audio Source

Units

The PRE-1 can connect to up to seven different audio

devices, using standard RCA analog connectors.

PHONO

Connects to a turntable using standard RCA type

connectors. Connect the Left output on the turntable to the

Left input of the PHONO INPUT section on the PRE-1,

and the Right output to the Right input of the PHONO

INPUT section of the PRE-1.

Also note the connection of the chassis ground tab

between the turntable and preamplifier. This is necessary

for audio signal reference so the PRE-1 processes signal

from the turntable with minimal unwanted noise.

Select the type of cartridge, either high output Moving

Magnet (MM) or low output Moving Coil (MC) by

moving the switch to the appropriate positions.

If you are not sure which type of cartridge you have, select

MM first and then if the noise level is too high, try

selecting MC instead.

The PHONO input is not designed for line level sources

such as CD players or other devices. Please ONLY

connect turntables with Moving Magnet or Moving Coil

needle cartridges to this input to avoid damage.

If you are using a separate preamplifier for your

turntable, do not use the PRE-1 Phono input section.

Use either the AUX1 orAUX2 inputs. The PRE-1 Phono

input is a high gain input, and turntable preamplifiers

have high gain output. Combining the two would result

in an extremely high gain signal that would cause

unwanted distortion.

Connects to a CD player using standard RCA type

connectors. Connect the Left output on the CD player to

the Left input of the CD INPUT section of the PRE-1, and

the Right output on the CD player to the Right input of the

CD INPUT section of the PRE-1.

* This is not a dedicated input, and can be used as an input

for a device other than a CD player.

TUNER

Connects to a Tuner using standard RCA type connectors.

Connect the Left output on the Tuner to the Left input of

the TUNER section of the PRE-1, and the Right output on

the Tuner to the Right input of the TUNER section of the

PRE-1.

* This is not a dedicated input, and can be used as an input

for a device other than a Tuner.

AUX1 & AUX2

These inputs can be used with most 2 channel audio

source devices, including DVD players, personal

computers, portable media players, MP3 players/docks,

etc. Depending on the type of media player and/or docking

station available, direct RCA outputs may not be available,

so a 1/8" stereo mini jack to RCA adapter may be

necessary to complete the connection. Analog outputs on

the audio devices are necessary to connect to the PRE-1.

TAPE

This 'loop' connects an external recording device to the

PRE-1 preamplifier via RCA outputs and inputs. While

this traditionally has been a cassette player or DAT player,

this connection could also be a hard drive based recording

device as long as the input and output connections are

analog RCA audio connections.

To enable the tape monitor loop you must connect to the

inputs AND outputs on the PRE-1 labeled "TAPE" on the

rear panel. To engage the tape monitor loop, select TAPE

from the PRE-1 front panel or remote.

Please note -these outputs are unaffected by any external

signal processing.

To engage the recording device, first press TAPE from the

front panel or remote and then it will allow you to

"monitor" the audio that the recording device will record.

When you are ready to record, engage the recording

device.

HT INPUT

Connects to an external multi-channel, or 'home theater'

processor using standard RCA type analog connectors.

Connect left, right, and subwoofer (if your front speakers

are not full range) analog outputs on the processor to the

PRE-1 HT inputs. When the HT BYPASS button is

selected, all PRE-1 functions are disabled, and it becomes

a pass-through for the connected external processor. The

HT inputs are only active when the PRE-1 is on.

Connecting To Amplifiers and Speakers

When connecting to amplifiers and speakers, make sure to

use the properly labeled left channel, right channel and

subwoofer connections.

Check to make sure that you have connected the proper

cables in the proper sequence:

• Left and right channel PRE-1 outputs (either full

range or High Pass) into left and right channel

amplifier inputs.

• Left and right channel amplifier outputs to left

and right speakers.

• PRE-1 subwoofer outputs for powered subwoofer

inputs.

NOTE: Do not connect speakers directly to the PRE-1.

1 2 ... 5 6 7 8 9 10 11 12 13 14

Kommentare zu diesen Handbüchern

Keine Kommentare

Sherbourn PRE-1 Anleitung zur Fehlerbehebung Seite 10

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Musikausrüstung Sherbourn PRE-1